Filter
Sort by: Most Viewed
Ask Question
0 votes
1 answer
5k views
How can I improve the 1 dB compression point of a mixer?
RF/Microwave Mixers mixers
0 votes
1 answer
5k views
I have the design choice to either have a high LO drive (around +20dBm) or a low LO drive (around +10 dBm) for my mixer. What should I choose?
RF/Microwave Mixers
0 votes
1 answer
5k views
You don’t specify VSWR on your datasheets. What is the typical VSWR for your mixers?
RF/Microwave Mixers mixers
0 votes
1 answer
5k views
Why are there so many diode types to choose from? How do I know what diode-type I should select?
RF/Microwave Mixers
0 votes
1 answer
5k views
BAL-0006SMG question
RF/Microwave Baluns
Hi, The datasheet for BAL-0006SMG specifies an insertion loss of 6dB. However, when I take time d...
  • umeshmja asked 5 years ago
  • last active 5 years ago
0 votes
1 answer
5k views
MLIQ-0218 option
RF/Microwave IR,IQ, and SSB Mixers
What does ‘I port configuration’ mean? Can I find that inform in datasheet?
  • John Park asked 5 years ago
  • last active 5 years ago
0 votes
1 answer
5k views
Which mixers have the best intermodulation distortion suppression?
RF/Microwave Mixers mixers   spurs
0 votes
1 answer
5k views
Why do higher barrier diodes have better intermodulation distortion suppression as compared to low barrier diodes?
RF/Microwave Mixers mixers   spurs
0 votes
1 answer
5k views
Can I improve the 1 dB compression point by increasing the LO drive level?
RF/Microwave Mixers mixers
39 votes
1 answer
4k views
T3 Mixers -- data sheet vs using ADM driver
RF/Microwave Mixers
It seems like the T3 mixer datasheets are mostly based on using the legacy A0010 LO driver, where...
7 votes
1 answer
2k views
IQ quadrature phase deviation of IQ-0307LXP
RF/Microwave IR,IQ, and SSB Mixers
I use an IQ-0307LXP mixer to create up-converted microwave pulses with single side band(SSB). I a...
  • jaseungku asked 3 years ago
  • last active 3 years ago
0 votes
0 answers
2k views
DLM-10SM_ Bias Current
General Microwave Engineering DLM-10SM
Hello Marki, We are using DLM-10SM Limiter in our Design. In order to set Limiting threshold we n...
0 votes
1 answer
2k views
Use a Filter with the ADM1-0026PA Amplifier
RF/Microwave Mixers
Howdy, I’m currently working on a design that will incorporate your T3-20 mixer.  In the sp...
  • Cameron asked 2 years ago
  • last active 2 years ago
0 votes
0 answers
1k views
MT3-0113LCQG spur performance IF 3 to 4 GHz LO 8 GHz RF 4 to 5 GHz
RF/Microwave Mixers
I am using MT3-0113LCQG to up convert 3 to 4 GHz (100 MHz step) to RF 4 to 5 GHz (100 MHz step) u...
0 votes
0 answers
1k views
ADS or AWR models for M2-0218, MT3-0113LCQG, M1-0310
RF/Microwave Mixers
we are using M2-0218, MT3-0113LCQG, M1-0310 mixers for various frequency of applications please p...
0 votes
1 answer
1k views
How would one drive one of our NLTLs so that they minimized AM noise?
RF/Microwave Frequency Multipliers multiplier    NLTLs
Our NLTL App Note states: The phase noise of a non-linear transmission line is outstanding. If ve...
0 votes
1 answer
982 views
Phase Noise of APM-6848
RF/Microwave Amplifiers amplifiers   phase noise
On the Marki website the APM6848 (bare die or module) is showing phase noise plots with a +9dBm a...
Showing 21 - 37 of 37 results
«12»

START TYPING AND PRESS ENTER TO SEARCH FOR MARKI PRODUCTS.